OATAO - Open Archive Toulouse Archive Ouverte Open Access Week

Production of binderless fiberboards from Calophyllum inophyllum twin-screw extrusion cakes through thermopressing

Amalia Kartika, Ika and Aulya Syamani, Firda and Vandenbossche, Virginie and Sablayrolles, Caroline and Vialle, Claire and Evon, Philippe Production of binderless fiberboards from Calophyllum inophyllum twin-screw extrusion cakes through thermopressing. (2017) In: 4th International Conference on Biobased Materials and Composites (29-31 March 2017) hosted in Nantes, 29 March 2017 - 31 March 2017 (Nantes, France).

[img]
Preview
(Document in English)

PDF (Author's version) - Requires a PDF viewer such as GSview, Xpdf or Adobe Acrobat Reader
1MB

Abstract

Vegetable oil from Calophyllum inophyllum kernels appears as a promising raw material for biodiesel production in Indonesia. For this, the oil must first be extracted and this is the twin-screw extrusion technology that has been used in that case to conduct such extraction. A two-step process was developed consisting in a mechanical pressing and then in the aqueous extraction of residual oil in the press cake. And, it should be noted that a fibrous residue (i.e. sunflower hull) was added in the second twin-screw reactor to facilitate the liquid/solid separation during the aqueous extraction stage. In the best condition tested, 63% of the oil was extracted. In addition, depending on the extrusion conditions used, residual oil content in the final cake varied from 16.7 to 19.1% of its dry matter instead of 74.0% inside the starting material (i.e. the kernel). In this study, the use of the final cakes as sources for fiberboard manufacture through thermopressing was investigated. These cakes can be considered as natural composites with lignocellulosic fibers from the fibrous residue and proteins from the Calophyllum inophyllum kernel breakdown process acting respectively as reinforcing fillers and a natural binder [1-2]. Cohesive self-bonded boards were thus obtained through thermopressing using the next molding conditions: 200 °C temperature, 20 MPa pressure and 300 s molding time. For the three cakes tested, part of their residual oil was expressed through the sidewall vents of the mold during molding, which was due to the applied pressure, and this contributed to the increase in the total vegetable oil recovery. In addition, the more the residual oil content in the cake, the more the oil expressed. However, oil expression during molding reduced the mechanical resistance of fiberboards, due to defects appearing within the material as the oil escaped. This contributed to a slight increase in the bending properties (from 12.1 to 15.4 MPa for flexural strength at break and from 1.9 to 2.0 GPa for elastic modulus) with the cake’s residual oil content decrease (from 19.1 to 16.7%). A significant improvement in the molding process consisted in conducting the cake’s deoiling prior thermopressing using a Soxhlet extraction apparatus and cyclohexane as extracting solvent. From this, the properties of the corresponding board (4.3 mm thickness and 1185 kg/m3 density) were much improved: 79° Shore D surface hardness (instead of 70° without deoiling), 23.7 MPa flexural strength at break and 3.1 GPa elastic modulus. In parallel, thickness swelling after 24 h immersion in water was 43.9% and it has decreased up to 27.6% after the board’s heat treatment (200 °C during 10 min). This optimal fiberboard complied with the French standard NF EN 312 (standard dedicated to the specifications for particleboards), type P7 (i.e. load bearing boards for use under high stress and in wet conditions) for flexural properties (recommendations of 21 MPa and 3.1 GPa for flexural strength at break and elastic modulus, respectively, for boards with a 4 to 6 mm thickness). However, thickness swelling after immersion in water will need to be significantly reduced to achieve the 10% recommended standard value.

Item Type:Conference or Workshop Item (UNSPECIFIED)
HAL Id:hal-01511523
Audience (conference):International conference without published proceedings
Uncontrolled Keywords:
Institution:Université de Toulouse > Institut National Polytechnique de Toulouse - INPT (FRANCE)
French research institutions > Institut National de la Recherche Agronomique - INRA (FRANCE)
Other partners > Bogor Agricultural University - IPB (INDONESIA)
Laboratory name:
Funders:
French Government and Campus France (PHC NUSANTARA mobility grant)
Statistics:download
Deposited By: Philippe EVON
Deposited On:21 Apr 2017 09:04

Repository Staff Only: item control page