OATAO - Open Archive Toulouse Archive Ouverte Open Access Week

Items where Person is "Baili, Maher"

Up a level
Export as [feed] Atom [feed] RSS 1.0 [feed] RSS 2.0
Group by: Item Type | No Grouping
Number of items: 20.

Article

Wagner, Vincent and Baili, Maher and Dessein, Gilles The relationship between the cutting speed, tool wear, and chip formation during Ti-5553 dry cutting. (2014) International Journal of Advanced Manufacturing Technology . ISSN 0268-3768

Msaddek, El Bechir and Bouaziz, Zoubeir and Baili, Maher and Dessein, Gilles Influence of interpolation type in high-speed machining (HSM). (2014) The International Journal of Advanced Manufacturing Technology, vol. 72 (n° 1-4). pp. 289-302. ISSN 0268-3768

Gassara, Bassem and Baili, Maher and Dessein, Gilles and Hbaieb, Moncef and Bouzid Saï, Wassila Feed rate modeling in circular–circular interpolation discontinuity for high-speed milling. (2013) The International Journal of Advanced Manufacturing Technology, vol. 65 (n° 9 -12). pp. 1619-1634. ISSN 0268-3768

Gassara, Bassem and Dessein, Gilles and Baili, Maher and Hbaieb, Moncef and Saï, Wassila Bouzid Analytical and experimental study of feed rate in high-speed milling. (2013) Machining Science and Technology, vol. 17 (n° 2). pp. 181-208. ISSN 1091-0344

Gassara, Bassem and Dessein, Gilles and Baili, Maher and Hbaieb, Moncef and Bouzid Saï, Wassila Kinematic behaviour modeling of the axes of a machining center in high speed milling. (2013) Advanced Materials Research, vol. 698 . pp. 39-48. ISSN 1022-6680

Smaoui, Moez and Bouaziz, Zoubeir and Zghal, Ali and Baili, Maher and Dessein, Gilles Compensation of a ball end tool trajectory in complex surface milling. (2012) International Journal of Machining and Machinability of Materials, vol. 11 (n° 1). pp. 51-68. ISSN 1748-5711

Popa, Andreï and Dessein, Gilles and Baili, Maher and Dutilh, Vincent Investigation of tool failure modes and machining disturbances using monitoring signals. (2012) Advanced Materials Research, vol. 423 . pp. 128-142. ISSN 1022-6680

Msaddek, El Bechir and Bouaziz, Zoubeir and Dessein, Gilles and Baili, Maher Optimization of pocket machining strategy in HSM. (2012) The International Journal of Advanced Manufacturing Technology, vol. 62 (n° 1-4). pp. 69-81. ISSN 0268-3768

Smaoui, Moez and Bouaziz, Zoubeir and Zghal, Ali and Dessein, Gilles and Baili, Maher Simulation of the deflected cutting tool trajectory in complex surface milling. (2011) The International Journal of Advanced Manufacturing Technology, vol. 56 (n° 5-8). pp. 463-474. ISSN 0268-3768

Msaddek, El Bechir and Bouaziz, Zoubeir and Baili, Maher and Dessein, Gilles Modeling and simulation of high-speed milling centers dynamics. (2011) The International Journal of Advanced Manufacturing Technology, vol. 53 (n ° 9-12). pp. 877-888. ISSN 0268-3768

Baili, Maher and Wagner, Vincent and Dessein, Gilles and Sallabery , Julien and Lallement, Daniel An Experimental Investigation of Hot Machining with Induction to Improve Ti-5553 Machinability. (2011) Applied Mechanics and Materials, vol. 62 . pp. 67-76. ISSN 1660-9336

Wagner, Vincent and Baili, Maher and Dessein, Gilles and Lallement, Daniel Experimental study of coated carbide tools behaviour: application for Ti-5-5-5-3 turning. (2011) International Journal of Machining and Machinability of Materials, Vol.9 (n° 3/4). pp. 233-248. ISSN 1748-5711

Wagner, Vincent and Baili, Maher and Dessein, Gilles and Lallement, Daniel Experimental characterization of behavior laws for titanium alloys: application to Ti5553. (2010) Key Engineering Materials, vol. 446 . pp. 147-155. ISSN 1662-9795

Conference or Workshop Item

Gassara, Bassem and Dessein, Gilles and Baili, Maher and Hbaieb, Moncef and Bouzid Saï, Wassila Modélisation du comportement cinématique des axes d'un centre d'usinage en fraisage à grande vitesse. (2012) In: 4th International Symposium on Aircraft Materials, 09-12 May 2012, Fez, Morocco .

Popa, Andreï and Baili, Maher and Dessein, Gilles and Dutilh, Vincent Identification of tool failure modes in drilling Udimet® 720 superalloy. (2011) In: International conference on structural analysis of advanced materials (ICSAAM2011), 7 September 2011 - 10 September 2011 (Sinaia, Romania).

Msaddek, El Bechir and Bouaziz, Zoubeir and Baili, Maher and Dessein, Gilles Modeling and simulation of high speed milling centers dynamics. (2010) In: 5th International Conference on Advances in Mechanical Engineering and Mechanics (ICAMEM2010), 18-20 Dec 2010, Hammamet, Tunisia .

Popa, Andreï and Dutilh, Vincent and Baili, Maher and Dessein, Gilles and Perrin, Géraldine Identification of influent factors on surface integrity in nickel-base superalloy drilling. (2010) In: 19th International Conference on Manufacturing Systems - ICMaS 2010, 11 November 2010 - 12 November 2010 (Bucharest, Romania).

Baili, Maher and Wagner, Vincent and Dessein, Gilles and Sallabery, Julien and Lallement, Daniel Influence de la température sur l’usinabilité du Ti-5-5-5-3. (2010) In: International Symposium on Aircraft Materials, 12 May 2010 - 14 May 2010 (Marrakech, Morocco).

Wagner, Vincent and Baili, Maher and Dessein, Gilles and Lallement, Daniel Behaviour laws comparison for titanium alloys machining: Application to Ti5553. (2009) In: International conference on structural analysis of advanced materials, 7 September 2009 - 10 September 2009 (Tarbes, France).

Book Section

Msaddek, El Bechir and Bouaziz, Zoubeir and Baili, Maher and Dessein, Gilles Simulation Tool of the HSM machine dynamic behavior. (2011) In: Milling: Operations, Applications and Industrial Effects. Nova Science Publishers, pp. 209-228. ISBN 978-1-61470-903-9

This list was generated on Fri Oct 24 15:10:00 2014 CEST.