OATAO - Open Archive Toulouse Archive Ouverte Open Access Week

Items where Laboratory is "Institut Clément Ader - ICA (Toulouse, France)"

Up a level
Export as [feed] Atom [feed] RSS 1.0 [feed] RSS 2.0
Group by: Item Type | No Grouping
Number of items: 272.

Article

Dubreuil, Sylvian and Salaün, Michel and Rodriguez, Emmanuel and Petitjean, Frank. Construction and identification of a D-Vine model applied to the probability distribution of modal parameters in structural dynamics. (2018) Mechanical Systems and Signal Processing, vol. 98. pp. 190-208. ISSN 0888-3270

Barus, Matthias and Welemane, Hélène and Nassiet, Valérie and Pastor, Marie-Laetitia and Cantarel, Arthur and Collombet, Francis and Crouzeix, Laurent and Grunevald, Yves-Henri. NDT-based design of joint material for the detection of bonding defects by infrared thermography. (2018) NDT&E International, vol. 93. pp. 157-163. ISSN 0963-8695

Susainathan, John and Eyma, Florent and De Luycker, Emmanuel and Cantarel, Arthur and Castanié, Bruno. Experimental investigation of impact behavior of wood-based sandwich structures. (2018) Composites Part A: Applied Science and Manufacturing, vol. 109. pp. 10-19. ISSN 1359-835X

Susainathan, John and Eyma, Florent and De Luycker, Emmanuel and Cantarel, Arthur and Castanier, Bruno. Manufacturing and quasi-static bending behavior of wood-based sandwich structures. ( In Press: 2017) Composite Structures, vol. 182 (n° 15). pp. 487-504. ISSN 0263-8223

Serra, Joël and Bouvet, Christophe and Castanié, Bruno and Petiot, Caroline. Experimental and numerical analysis of Carbon Fiber Reinforced Polymer notched coupons under tensile loading. (2017) Composite Structures, vol. 181. pp. 145-157. ISSN 0263-8223

Serra, Joël and Pierré, Jean-Emmanuel and Passieux, Jean-Charles and Périé, Jean-Noel and Bouvet, Christophe and Castanié, Bruno and Petiot, Caroline. Validation and modeling of aeronautical composite structures subjected to combined loadings: The VERTEX project. Part 2: Load envelopes for the assessment of panels with large notches. (2017) Composite Structures, vol. 180. pp. 550-567. ISSN 0263-8223

Serra, Joël and Pierré, Jean-Emmanuel and Passieux, Jean-Charles and Périé, Jean-Noel and Bouvet, Christophe and Castanié, Bruno. Validation and Modeling of Aeronautical Composite Structures Subjected to Combined Loadings: the VERTEX Project. Part 1: Experimental Setup, FE-DIC Instrumentation and Procedures. (2017) Composite Structures, vol. 179. pp. 224-244. ISSN 0263-8223

Paroissien, Eric and Lachaud, Frédéric and Schwartz, Sébastien and Da Veiga, Anthony and Barrière, Patrick. Simplified stress analysis of hybrid (bolted/bonded) joints. (2017) International Journal of Adhesion and Adhesives, vol. 77. pp. 183-197. ISSN 0143-7496

Planques, Pierre and Vidal, Vanessa and Lours, Philippe and Proton, Vincent and Crabos, Fabrice and Huez, Julitte and Viguier, Bernard. Mechanical and thermo-physical properties of plasma-sprayed thermal barrier coatings: a literature survey. (2017) Oxidation of Metals, vol. 88 (n° 1-2). pp. 133-143. ISSN 0030-770X

Dubary, Nicolas and Taconet, Gabriel and Bouvet, Christophe and Vieille, Benoit. Influence of temperature on the impact behavior and damage tolerance of hybrid woven-ply thermoplastic laminates for aeronautical applications. (2017) Composite Structures, vol. 168. pp. 663-674. ISSN 0263-8223

Bouclier, Robin and Passieux, Jean-Charles and Salaün, Michel. Development of a new, more regular, mortar method for the coupling of NURBS subdomains within a NURBS patch: Application to a non-intrusive local enrichment of NURBS patches. (2017) Computer Methods in Applied Mechanics and Engineering, vol. 316. pp. 123-150. ISSN 0045-7825

Bessaguet, Camille and Dantras, Eric and Lacabanne, Colette and Chevalier, Mathieu and Michon, Guilhem. Piezoelectric and mechanical behavior of NaNbO3/PEKK lead-free nanocomposites. (2017) Journal of Non-Crystalline Solids, vol. 459. pp. 83-87. ISSN 0022-3093

Lisle, Teddy and Pastor, Marie-Laetitia and Bouvet, Christophe and Margueres, Philippe. Damage of woven composite under translaminar cracking tests using infrared thermography. (2017) Composite Structures, vol. 161. pp. 275-286. ISSN 0263-8223

Murdoch, Naomi and Martinez, Iris Avila and Sunday, Cecily and Zenou, Emmanuel and Cherrier, Olivier and Cadu, Alexandre and Gourinat, Yves. An experimental study of low-velocity impacts into granular material in reduced gravity. (2017) Monthly Notices of the Royal Astronomical Society, vol. 468 (n° 2). pp. 1259-1272. ISSN 0035-8711

Barus, Matthias and Welemane, Hélène and Collombet, Francis and Pastor, Marie-Laetitia and Cantarel, Arthur and Crouzeix, Laurent and Grunevald, Yves-Henri and Nassiet, Valérie. Bonded repair issues for composites: An investigation approach based on infrared thermography. (2017) NDT & E International, vol. 85. pp. 27-33. ISSN 0963-8695

Chiplunkar, Ankit and Rachelson, Emmanuel and Colombo, Michele and Morlier, Joseph. Approximate inference in related multi-output Gaussian Process Regression. (2017) Lecture Notes in Computer Science. pp. 88-103. ISSN 0302-9743

Mezeix, Laurent and Dols, Simon and Bouvet, Christophe and Castanié, Bruno and Giavarini, Jean-Paul and Hongkarnjanakul, Natthawat. Experimental analysis of impact and post-impact behaviour of inserts in Carbon sandwich structures. (2017) Journal of Sandwich Structures and Materials. ISSN 1099-6362 (Unpublished)

Fogel, Mathieu and Parlevliet, Patricia and Olivier, Philippe and Dantras, Eric. Manufacturing of conductive structural composites through spraying of CNTs/epoxy dispersions on dry carbon fiber plies. (2017) Composites Part A: Applied Science and Manufacturing, vol. 100. pp. 40-47. ISSN 1359-835X

Rivière, Lisa and Lonjon, Antoine and Dantras, Eric and Lacabanne, Colette and Olivier, Philippe and Rocher Gleizes, Nathalie. Silver fillers aspect ratio influence on electrical and thermal conductivity in PEEK/Ag nanocomposites. (2016) European Polymer Journal, vol. 85. pp. 115-125. ISSN 0014-3057

Piollet, Elsa and Poquillon, Dominique and Michon, Guilhem. Dynamic hysteresis modelling of entangled cross-linked fibres in shear. (2016) Journal of Sound and Vibration, vol. 383. pp. 248-264. ISSN 0022-460X

Pozzolini, Cédric and Renard, Yves and Salaün, Michel. Energy conservative finite element semi-discretization for vibro-impacts of plates on rigid obstacles. (2016) ESAIM: Mathematical Modelling and Numerical Analysis, vol. 50 (n° 6). pp. 1585-1613. ISSN 0764-583X

Destic, Fabien and Bouvet, Christophe. Impact damages detection on composite materials by THz imaging. (2016) Case Studies in Nondestructive Testing and Evaluation, vol. 6. pp. 53-62. ISSN 2214-657

Charlotte, Miguel. An atomistically-meaningful pseudocontinuum representation for the finite monatomic chain with harmonic nearest-neighbor interactions. (2016) International Journal of Solids and Structures, vol. 97-98. pp. 209-225. ISSN 0020-7683

Ostré, Benjamin and Bouvet, Christophe and Minot, Clément and Aboissière, Jacky. Finite Element analysis of CFRP laminates subjected to compression after edge impact. (2016) Composite Structures, vol. 153. pp. 478-489. ISSN 0263-8223

Ostré, Benjamin and Bouvet, Christophe and Minot, Clément and Aboissière, Jacky. Experimental analysis of CFRP laminates subjected to compression after edge impact. (2016) Composite Structures, vol. 152. pp. 767-778. ISSN 0263-8223

Abdulhamid, Hakim and Bouvet, Christophe and Michel, Laurent and Aboissière, Jacky and Minot, Clément. Numerical simulation of impact and compression after impact of asymmetrically tapered laminated CFRP. (2016) International Journal of Impact Engineering, vol. 95. pp. 154-164. ISSN 0734-743X

Abdulhamid, Hakim and Bouvet, Christophe and Michel, Laurent and Aboissière, Jacky and Minot, Clément. Experimental study of compression after impact of asymmetrically tapered composite laminate. (2016) Composite Structures, vol. 149. pp. 292-303. ISSN 0263-8223

Sunday, Cecily and Murdoch, Naomi and Cherrier, Olivier and Morales Serrano, Sara and Valeria Nardi, Claudia and Janin, Tristan and Avila Martinez, Iris and Gourinat, Yves and Mimoun, David. A novel facility for reduced-gravity testing: A setup for studying low-velocity collisions into granular surfaces. (2016) Review of Scientific Instruments, vol. 87 (n° 8). pp. 084504. ISSN 0034-6748

Serra, Joël and Bouvet, Christophe and Castanié, Bruno and Petiot, Caroline. Scaling effect in notched composites: The Discrete Ply Model approach. (2016) Composite Structures, vol. 148. pp. 127-143. ISSN 0263-8223

Bennani, Lokman and Villedieu, Philippe and Salaün, Michel. A mixed adhesion–brittle fracture model and its application to the numerical study of ice shedding mechanisms. (2016) Engineering Fracture Mechanics, vol. 158. pp. 59-80. ISSN 0013-7944

Fabas, Aurélien and Monceau, Daniel and Josse, Claudie and Lamesle, Pascal and Rouaix-Vande Put, Aurélie. Mechanism of metal dusting corrosion by pitting of a chromia-forming alloy at atmospheric pressure and low gas velocity. (2016) Corrosion Science, vol. 107. pp. 204-210. ISSN 0010-938X

Bouhlel, Mohamed Amine and Bartoli, Nathalie and Otsmane, Abdelkader and Morlier, Joseph. Improving kriging surrogates of high-dimensional design models by Partial Least Squares dimension reduction. (2016) Structural and Multidisciplinary Optimization, vol. 53 (n° 5). pp. 935-952. ISSN 1615-147X

Budinger, Marc and Pommier-Budinger, Valérie and Napias, Gael and Costa Da Silva, Arthur. Ultrasonic ice protection systems: analytical and numerical models for architecture trade-off. (2016) Journal of Aircraft, vol. 53 (n° 3). pp. 680-690. ISSN 0021-8669

Duval, Mickaël and Passieux, Jean-Charles and Salaün, Michel and Guinard, Stéphane. Non-intrusive Coupling: Recent Advances and Scalable Nonlinear Domain Decomposition. (2016) Archives of Computational Methods in Engineering, vol. 23 (n° 1). pp. 17-38. ISSN 1134-3060

Bouhlel, Mohamed Amine and Bartoli, Nathalie and Ostmane, Abdelkader and Morlier, Joseph. An improved approach for estimating the hyperparameters of the kriging model for high-dimensional problems through the partial least squares method. (2016) Mathematical Problems in Engineering, vol. 2016. pp. 1-11. ISSN 1024-123X

Munoz Cuartas, Victor and Vales, Benjamin and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Damage detection in CFRP by coupling acoustic emission and infrared thermography. (2016) Composites Part B: Engineering, vol. 85. pp. 68-75. ISSN 1359-8368

Vales, Benjamin and Munoz Cuartas, Victor and Welemane, Hélène and Pastor, Marie-Laetitia and Trajin, Baptiste and Perrin, Marianne and Cantarel, Arthur and Karama, Moussa. Heat source estimation in anisotropic materials. (2016) Composite Structures, vol. 136. pp. 287-296. ISSN 0263-8223

Bouclier, Robin and Passieux, Jean-Charles and Salaün, Michel. Local enrichment of NURBS patches using a non-intrusive coupling strategy: Geometric details, local refinement, inclusion, fracture. (2016) Computer Methods in Applied Mechanics and Engineering, vol. 300. pp.1-26. ISSN 0045-7825

Mohd Zawawi, Fazila and Lv, Peng and Prothin, Sebastien and Morlier, Joseph and Bénard, Emmanuel and Moschetta, Jean-Marc. Performance Enhancement of Tilt-Body Micro Air Vehicle by Use of Orthotropic Laminated Proprotors. (2016) Applied Mechanics and Materials, vol. 819. pp. 585-590. ISSN 1660-9336

Ge, Yangyang and Gong, Xiao-Jing and Hurez, Anita and De Luycker, Emmanuel. Test methods for measuring pure mode III delamination toughness of composite. (2016) Polymer Testing, vol. 55. pp. 261-268. ISSN 0142-9418

Passieux, Jean-Charles and Périé, Jean-Noel and Salaün, Michel. A dual domain decomposition method for finite element digital image correlation. (2015) International Journal for Numerical Methods in Engineering, vol.102 (n°10). pp.1670-1682. ISSN 0029-5981

Ostré, Benjamin and Bouvet, Christophe and Minot, Clément and Aboissière, Jacky. Edge impact modeling on stiffened composite structures. (2015) Composite Structures, vol. 126. pp. 314-328. ISSN 0263-8223

Lélias, Guillaume and Paroissien, Eric and Lachaud, Frédéric and Morlier, Joseph and Schwartz, Sébastien and Gavoille, Cyril. An extended semi-analytical formulation for fast and reliable mode I/II stress analysis of adhesively bonded joints. (2015) International Journal of Solids and Structures, vol. 62. pp. 18-38. ISSN 0020-7683

Lisle, Teddy and Bouvet, Christophe and Pastor, Marie-Laetitia and Rouault, Thomas and Margueres, Philippe. Damage of woven composite under tensile and shear stress using infrared thermography and micrographic cuts. (2015) Journal of Materials Science, vol. 50 (n° 18). pp. 6154-6170. ISSN 0022-2461

Lisle, Teddy and Bouvet, Christophe and Hongkarnjanakul, Natthawat and Pastor, Marie-Laetitia and Rivallant, Samuel and Margueres, Philippe. Measure of fracture toughness of compressive fiber failure in composite structures using infrared thermography. (2015) Composites Science and Technology, vol. 112. pp. 22-33. ISSN 0266-3538

Espinosa, Christine and Lachaud, Frédéric and Limido, Jérôme and Lacome, Jean-Luc and Bisson, Antoine and Charlotte, Miguel. Coupling continuous damage and debris fragmentation for energy absorption prediction by cfrp structures during crushing. (2015) Computational Particle Mechanics, vol. 2 (n° 1). pp. 1-17. ISSN 2196-4378

Mezeix, Laurent and Poquillon, Dominique and Bouvet, Christophe. Entangled cross-linked fibres for an application as core material for sandwich structures - Part I: Experimental investigation. (2015) Applied Composite Materials. pp. 1-16. ISSN 0929-189X

Lv, Peng and Prothin, Sebastien and Mohd Zawawi, Fazila and Bénard, Emmanuel and Morlier, Joseph and Moschetta, Jean-Marc. Performance improvement of small-scale rotors by passive blade twist control. (2015) Journal of Fluids and Structures, vol. 55. pp. 25-41. ISSN 0889-9746

Fogel, Mathieu and Parlevliet, Patricia and Geistbeck, Matthias and Olivier, Philippe and Dantras, Eric. Thermal, rheological and electrical analysis of MWCNTs/epoxy matrices. (2015) Composites Science and Technology, vol. 110. pp. 118-125. ISSN 0266-3538

Salaün, Michel and Salmon, Stéphanie. Low-order finite element method for the well-posed bidimensional Stokes problem. (2015) IMA Journal of Numerical Analysis, vol. 35 (n° 1). pp. 427-453. ISSN 0272-4979

Abdulhamid, Hakim and Bouvet, Christophe and Michel, Laurent and Aboissière, Jacky and Minot, Clément. Influence of internally dropped-off plies on the impact damage of asymmetrically tapered laminated CFRP. (2015) Composites Part A: Applied Science and Manufacturing, vol. 68. pp. 110-120. ISSN 1359-835X

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Determination of the elastic properties in CFRP composites: comparison of different approaches based on tensile tests and ultrasonic characterization. (2015) Advances in Aircraft and Spacecraft Science, vol. 2 (n° 3). pp. 249-260. ISSN 2287-528X

Mezeix, Laurent and Poquillon, Dominique and Bouvet, Christophe. Entangled cross-linked fibres for an application as core material for sandwich structures - Part II: Analytical model. (2015) Applied Composite Materials. pp. 1-13. ISSN 0929-189X

Liu, Yinghui and Vidal, Vanessa and Le Roux, Sabine and Blas, Fabien and Ansart, Florence and Lours, Philippe. Influence of isothermal and cyclic oxidation on the apparent interfacial toughness in thermal barrier coating systems. (2015) Journal of the European Ceramic Society, vol. 35 (n° 15). pp. 4269-4275. ISSN 0955-2219

Carponcin, Delphine and Dantras, Eric and Michon, Guilhem and Dandurand, Jany and Aridon, Gwenaëlle and Levallois, Franck and Cadiergues, Laurent and Lacabanne, Colette. New hybrid polymer nanocomposites for passive vibration damping by incorporation of carbon nanotubes and lead zirconate titanate particles. (2015) Journal of Non-Crystalline Solids, vol. 409. pp. 20-26. ISSN 0022-3093

Copin, Etienne and Sentenac, Thierry and Le Maoult, Yannick and Blas, Fabien and Ansart, Florence and Vidal, Vanessa and Lours, Philippe. Feasibility of luminescent multilayer sol-gel thermal barrier coating manufacturing for future applications in through-thickness temperature gradient sensing. (2014) Surface and Coatings Technology, vol. 260. pp. 90-96. ISSN 0257-8972

Morlier, Joseph and Niemann, Hanno and Shahdin, Amir. Topology optimization for robust damage localization using aggregated FRFs statistical criteria. (2014) Applied Mechanics and Materials, vol. 629. pp. 513-518. ISSN 1662-7482

Bennani, Lokman and Villedieu, Philippe and Salaün, Michel and Trontin, Pierre. Numerical simulation and modeling of ice shedding: Process initiation. (2014) Computers & Structures, 142. pp. 15-27. ISSN 0045-7949

Hongkarnjanakul, Natthawat and Rivallant, Samuel and Bouvet, Christophe and Miranda, Arturo. Permanent indentation characterization for low-velocity impact modelling using three-point bending test. (2014) Journal of Composite Materials, vol. 48 (n° 20). pp. 2441-2454. ISSN 0021-9983

Foucaud, Simon and Michon, Guilhem and Gourinat, Yves and Pelat, Adrien and Gautier, François. Artificial cochlea and acoustic black hole travelling waves observation: Model and experimental results. (2014) Journal of Sound and Vibration, vol. 333 (n° 15). pp. 3428-3439. ISSN 0022-460X

Achard, Victor and Bouvet, Christophe and Castanié, Bruno and Chirol, Clément. Discrete ply modelling of open hole tensile tests. (2014) Composite Structures, vol. 113. pp. 369-381. ISSN 0263-8223

Seguy, Sébastien and Arnaud, Lionel and Insperger, Tamás. Chatter in interrupted turning with geometrical defects: an industrial case study. (2014) The International Journal of Advanced Manufacturing Technology, vol. 75 (n° 1-4). pp. 45-56. ISSN 0268-3768

Ostré, Benjamin and Bouvet, Christophe and Lachaud, Frédéric and Minot, Clément and Aboissière, Jacky. Edge impact damage scenario on stiffened composite structure. (2014) Journal of Composite Materials. ISSN 0021-9983

Rivallant, Samuel and Bouvet, Christophe and Abi Abdallah, Elias and Broll, Bernhard and Barrau, Jean-Jacques. Experimental analysis of CFRP laminates subjected to Compression After Impact: the role of impact-induced cracks in failure. (2014) Composite Structures, vol. 111. pp. 147-157. ISSN 0263-8223

Pin, Lisa and Vidal, Vanessa and Blas, Fabien and Ansart, Florence and Duluard, Sandrine and Bonino, Jean-Pierre and Le Maoult, Yannick and Lours, Philippe. Optimized sol–gel thermal barrier coatings for long-term cyclic oxidation life. (2014) Journal of the European Ceramic Society, vol. 34 (n° 4). pp. 961-974. ISSN 0955-2219

Dubreuil, Sylvain and Berveiller, Marc and Petitjean, Frank and Salaün, Michel. Construction of bootstrap confidence intervals on sensitivity indices computed by polynomial chaos expansion. (2014) Reliability Engineering & System Safety, vol. 121. pp. 263-275. ISSN 0951-8320

Israr, Haris Ahmad and Rivallant, Samuel and Bouvet, Christophe and Barrau, Jean-Jacques. Finite element simulation of 0°/90° CFRP laminated plates subjected to crushing using a free-face-crushing concept. (2014) Composites Part A: Applied Science and Manufacturing, vol. 62. pp. 16-25. ISSN 1359-835X

Busca, Damien and Fazzini, Marina and Lorrain, Bernard and Mistou, Sébastien and Karama, Moussa and Pastor, Marie-Laetitia. High-Speed Stereo Digital Image Correlation: Application to Biaxial Fatigue. (2014) Strain. ISSN 0039-2103

Vieille, Benoit and Casado, Victor Manuel and Bouvet, Christophe. Influence of matrix toughness and ductility on the compression-after-impact behavior of woven-ply thermoplastic- and thermosetting-composites: A comparative study. (2014) Composite Structures, vol. 110. pp. 207-218. ISSN 0263-8223

Israr, Haris Ahmad and Hongkarnjanakul, Natthawat and Rivallant, Samuel and Bouvet, Christophe. Post-Impact Investigation of CFRP Laminated Plate. (2014) Jurnal Teknologi, vol. 71 (n° 2). pp. 71-78. ISSN 0127-9696

Pommier-Budinger, Valérie and Budinger, Marc. Sizing optimization of piezoelectric smart structures with meta-modeling techniques for dynamic applications. (2014) International Journal of Applied Electromagnetics and Mechanics. ISSN 1875-8800

Mohd Zawawi, Fazila and Lv, Peng and Prothin, Sebastien and Morlier, Joseph and Moschetta, Jean-Marc and Bénard, Emmanuel. Study of a flexible UAV proprotor. (2014) International Journal of Engineering Systems Modelling and Simulation, vol. 6 (n° 3/4). pp. 149-161. ISSN 1755-9758

Lv, Peng and Mohd Zawawi, Fazila and Bénard, Emmanuel and Prothin, Sebastien and Moschetta, Jean-Marc and Morlier, Joseph. An Application of Adaptive Blades on Convertible MAVs. (2013) International Journal of Micro Air Vehicles, vol. 5 (n° 4). pp. 229-243. ISSN 1756-8293

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Application of non destructive testing to the detection of aeronautical defects in composite structure. (2013) Nonconventional Technologies Review, vol. 4. pp. 58-64. ISSN 1454-3087

Amiot, Fabien and Bornert, Michel and Doumalin, Pascal and Dupré, Jean-Christophe and Fazzini, Marina and Orteu, Jean-José and Poilane, Christophe and Robert, Laurent and Rotinat, René and Toussaint, Eveline and Wattrisse, Bertrand and Wienin, Jean-Samuel. Assessment of digital image correlation measurement accuracy in the ultimate error regime: main results of a collaborative benchmark. (2013) Strain, vol. 49 (n°6). pp. 483-496. ISSN 1475-1305

Pozzolini, Cédric and Renard, Yves and Salaün, Michel. The singular dynamic method for dynamic contact of thin elastic structures. (2013) ESAIM: Proceedings, vol. 42. pp. 20-33. ISSN 1270-900X

Vermesse, Eric and Mabru, Catherine and Arurault, Laurent. Surface integrity after pickling and anodization of Ti–6Al–4V titanium alloy. (2013) Applied Surface Science, vol. 285 (Part B). pp. 629-637. ISSN 0169-4332

Kolopp, Amélie and Rivallant, Samuel and Bouvet, Christophe. Experimental study of sandwich structures as armour against medium-velocity impacts. (2013) International Journal of Impact Engineering, vol. 61. pp. 24-35. ISSN 0734-743X

Ben Slima, Khalil and Penazzi, Luc and Mabru, Catherine and Ronde-Oustau, François. Fatigue analysis-based numerical design of stamping tools made of cast iron. (2013) The International Journal of Advanced Manufacturing Technology, vol. 67 (n° 5-8). pp. 1643-1650. ISSN 0268-3768

Kolopp, Amélie and Alvarado, Raquel and Rivallant, Samuel and Bouvet, Christophe. Modeling impact on aluminium sandwich including velocity effects in honeycomb core. (2013) Journal of Sandwich Structures and Materials, vol. 13 (n° 6). pp. 733-757. ISSN 1099-6362

Giraud, Xavier and Sartor, Marc and Roboam, Xavier and Sareni, Bruno and Piquet, Hubert and Budinger, Marc and Vial, Sébastien. Load allocation problem for optimal design of aircraft electrical power system. (2013) International Journal of Applied Electromagnetics and Mechanics, vol. 43 (n° 1-2). pp. 1-13. ISSN 1383-5416

Hachemane, Belkacem and Zitoune, Redouane and Bezzazi, Boudjema and Bouvet, Christophe. Sandwich composites impact and indentation behaviour study. (2013) Composites Part B: Engineering, vol. 51. pp. 1-10. ISSN 1359-8368

Vieille, Benoit and Casado, Victor Manuel and Bouvet, Christophe. About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study. (2013) Composite Structures, vol. 101. pp. 9-21. ISSN 0263-8223

Garnier, Christian and Pastor, Marie-Laetitia and Lorrain, Bernard and Pantalé, Olivier. Fatigue behaviour of impacted composite structures. (2013) Composite Structures, vol. 100. pp. 443-450. ISSN 0263-8223

Roussouly, Nicolas and Petitjean, Frank and Salaün, Michel. A new adaptive response surface method for reliability analysis. (2013) Probabilistic Engineering Mechanics, vol. 32. pp. 103-115. ISSN 0266-8920

Pin, Lisa and Pilgrim, Christopher and Feist, Jörg and Le Maoult, Yannick and Ansart, Florence and Lours, Philippe. Characterisation of thermal barrier sensor coatings synthesised by sol–gel route. (2013) Sensors and Actuators A: Physical, vol. 199. pp. 289-296. ISSN 0924-4247

Maillet, Irène and Michel, Laurent and Rico, Germain and Fressinet, Mathieu and Gourinat, Yves. A new test methodology based on structural resonance for mode I fatigue delamination growth in an unidirectional composite. (2013) Composite Structures, vol. 97. pp. 353-362. ISSN 0263-8223

Chaussumier, Michel and Mabru, Catherine and Shahzad, Majid and Chieragatti, Rémy and Rezaï-Aria, Farhad. A predictive fatigue life model for anodized 7050 aluminium alloy. (2013) International Journal of Fatigue, vol. 48. pp. 205-213. ISSN 0142-1123

Israr, Haris Ahmad and Rivallant, Samuel and Barrau, Jean-Jacques. Experimental investigation on mean crushing stress characterization of carbon–epoxy plies under compressive crushing mode. (2013) Composite Structures, vol. 96. pp. 357-364. ISSN 0263-8223

Mousseigne, Michel and Landon, Yann and Seguy, Sébastien and Dessein, Gilles and Redonnet, Jean-Max. Predicting the dynamic behaviour of torus milling tools when climb milling using the stability lobes theory. (2013) International Journal of Machine Tools and Manufacture, vol. 65. pp. 47-57. ISSN 0890-6955

Pin, Lisa and Ansart, Florence and Bonino, Jean-Pierre and Le Maoult, Yannick and Vidal, Vanessa and Lours, Philippe. Reinforced sol–gel thermal barrier coatings and their cyclic oxidation life. (2013) Journal of the European Ceramic Society, vol. 33 (n° 2). pp. 269-276. ISSN 0955-2219

Abdulhamid, Hakim and Kolopp, Amélie and Bouvet, Christophe and Rivallant, Samuel. Experimental and numerical study of AA5086-H111 aluminum plates subjected to impact. (2013) International Journal of Impact Engineering, vol. 51. pp. 1-12. ISSN 0734-743X

Le Dref, John and Eyma, Florent and Dessein, Gilles and Denaud, Louis Etienne and Landon, Yann. Comparative study of tools in drilling composites T700-M21 and T800-M21. (2013) Advanced Materials Research, vol. 698. pp. 59-68. ISSN 1662-8985

Lisle, Teddy and Bouvet, Christophe and Pastor, Marie-Laetitia and Margueres, Philippe and Prieto Corral, Roberto. Damage analysis and fracture toughness evaluation in a thin woven composite laminate under static tension using infrared thermography. (2013) Composites Part A: Applied Science and Manufacturing, vol. 53. pp. 75-87. ISSN 1359-835X

Cherrier, Olivier and Selva, Pierre and Pommier-Budinger, Valérie and Lachaud, Frédéric and Morlier, Joseph. Damage localization map using electromechanical impedance spectrums and inverse distance weighting interpolation: Experimental validation on thin composite structures. (2013) Structural Health Monitoring, vol. 12 (n° 4). pp. 311-324. ISSN 1475-9217

Paroissien, Eric and Gaubert, Frédéric and Da Veiga, Anthony and Lachaud, Frédéric. Elasto-Plastic Analysis of Bonded Joints with Macro-Elements. (2013) Journal of Adhesion Science and Technology, vol. 27 (n° 13). pp. 1464-1498. ISSN 0169-4243

Rivallant, Samuel and Bouvet, Christophe and Hongkarnjanakul, Natthawat. Failure analysis of CFRP laminates subjected to Compression After Impact: FE simulation using discrete interface elements. (2013) Composites Part A: Applied Science and Manufacturing, vol. 55. pp. 83-93. ISSN 1359-835X

Péronnet, Elodie and Pastor, Marie-Laetitia and Huillery, Richard and Dalverny, Olivier and Mistou, Sébastien and Karama, Moussa and Génot, Sylvain. Non destructive investigation of defects in composite structures by fullfield measurement methods. (2013) Key Engineering Materials, vol. 550. pp. 135-142. ISSN 1013-9826

Rouault, Thomas and Bouvet, Christophe and Nègre, Vincent and Rauch, Patrice. Reversible Rail Shear Apparatus Applied to the Study of Woven Laminate Shear Behavior. (2013) Experimental Mechanics. ISSN 0014-4851

Sanches, Leonardo and Alazard, Daniel and Michon, Guilhem and Berlioz, Alain. Robustness Analysis of Helicopter Ground Resonance with Parametric Uncertainties in Blade Properties. (2013) Journal of Guidance, Control, and Dynamics, vol. 36 (n° 1). pp. 272-281. ISSN 0731-5090

Selva, Pierre and Cherrier, Olivier and Pommier-Budinger, Valérie and Lachaud, Frédéric and Morlier, Joseph. Smart monitoring of aeronautical composites plates based on electromechanical impedance measurements and artificial neural networks. (2013) Engineering Structures, vol. 56. pp. 794-804. ISSN 0141-0296

Hongkarnjanakul, Natthawat and Bouvet, Christophe and Rivallant, Samuel. Validation of low velocity impact modelling on different stacking sequences of CFRP laminates and influence of fibre failure. (2013) Composite Structures, vol. 106. pp. 549-559. ISSN 0263-8223

Pozzolini, Cédric and Renard, Yves and Salaün, Michel. Vibro-impact of a plate on rigid obstacles: existence theorem, convergence of a scheme and numerical simulations. (2013) IMA Journal of Numerical Analysis, vol. 33 (n° 1). pp. 261 -294. ISSN 0272-4979

El Sawi, Ihab and Olivier, Philippe and Demont, Philippe and Bougherara, Habiba. Processing and electrical characterization of a unidirectional CFRP composite filled with double walled carbon nanotubes. (2012) Composites Science and Technology, vol. 73. pp. 19-26. ISSN 0266-3538

El Sawi, Ihab and Olivier, Philippe and Demont, Philippe and Bougherara, Habiba. Investigation of the effect of double-walled carbon nanotubes on the curing reaction kinetics and shear flow of an epoxy resin. (2012) Journal of Applied Polymer Science, vol. 126 (n°1). pp. 358-366. ISSN 0021-8995

Adam, Louis and Bouvet, Christophe and Castanié, Bruno and Daidie, Alain and Bonhomme, Elodie. Discrete ply model of circular pull-through test of fasteners in laminates. (2012) Composite Structures, vol. 94 (n° 10). pp. 3082-3091.

Renault, Cyril and Roche, Jérôme and Ciumag, Mihaela Raluca and Tzedakis, Théodore and Colin, Stéphane and Serrano, Karine and Reynes, Olivier and André-Barrès, Christiane and Winterton, Peter. Design and optimization of electrochemical microreactors for continuous electrosynthesis. (2012) Journal of Applied Electrochemistry, vol. 42 (n° 9). pp. 667-677. ISSN 0021-891X

Tawk, Issam and Aubry, Julien and Navarro, Pablo and Ferrero, Jean-François and Marguet, Steven and Rivallant, Samuel and Lemaire, Sandrine and Rauch, Patrice. Study of impact on helicopter blade. (2012) Engineering Failure Analysis, vol. 24. pp. 38-45. ISSN 1350-6307

Lasry, Jérémie and Renard, Yves and Salaün, Michel. Stress intensity factors computation for bending plates with extended finite element method. (2012) International Journal for Numerical Methods in Engineering, vol. 91 (n° 9). pp. 909-928. ISSN 0029-5981

Sanches, Leonardo and Michon, Guilhem and Berlioz, Alain and Alazard, Daniel. Parametrically excited helicopter ground resonance dynamics with high blade asymmetries. (2012) Journal of Sound and Vibration, vol. 331 (n° 16). pp. 3897-3913. ISSN 0022-460X

Goueffon, Yann and Aldebert, Grégory and Mabru, Catherine and Arurault, Laurent and Tonon, Claire and Guigue, Pascale. Flaking of black anodic films in space environment: Ageing and numerical simulation. (2012) Mechanics of Materials, vol. 45. pp. 72-82. ISSN 0167-6636

Péronnet, Elodie and Eyma, Florent and Welemane, Hélène and Mistou, Sébastien. Characterization and comparison of defects detection limits of ultrasonic non destructive techniques. (2012) Key Engineering Materials, vol. 498. pp. 79-88. ISSN 1013-9826

Senatore, Johanna and Segonds, Stéphane and Rubio, Walter and Dessein, Gilles. Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: Application to milling by zones. (2012) Computer-Aided Design, vol. 44 (n° 12). pp. 1151-1160. ISSN 00104485

Shahzad, Majid and Chaussumier, Michel and Chieragatti, Rémy and Mabru, Catherine and Rezaï-Aria, Farhad. Effect of sealed anodic film on fatigue performance of 2214-T6 aluminium alloy. (2012) Surface and Coatings Technology, vol. 206 (n° 11-12). pp. 2733-2739. ISSN 0257-8972

Rahmé, Pierre and Bouvet, Christophe and Rivallant, Samuel and Fascio, Valia and Valembois, Guy. Experimental investigation of impact on composite laminates with protective layers. (2012) Composites Science and Technology, vol. 72 (n° 2). pp. 182-189. ISSN 0266-3538

Bouvet, Christophe and Rivallant, Samuel and Barrau, Jean-Jacques. Low velocity impact modeling in composite laminates capturing permanent indentation. (2012) Composites Science and Technology, vol. 72 (n° 16). pp. 1977-1988. ISSN 0266-3538

Renault, Cyril and Colin, Stéphane and Orieux, Stéphane and Cognet, Patrick and Tzedakis, Théodore. Optimal design of multi-channel microreactor for uniform residence time distribution. (2012) Microsystem Technologies, vol. 18 (n° 2). pp. 209-223. ISSN 0946-7076

Njionhou, Alvine and Berthet, Florentin and Castanié, Bruno and Bouvet, Christophe. Relationships between LRI process parameters and impact and post-impact behaviour of stitched and unstitched NCF laminates. (2012) Applied Composite Materials, vol. 19 (n° 6). pp. 885-899. ISSN 0929-189X

Pin, Lisa and Ansart, Florence and Bonino, Jean-Pierre and Le Maoult, Yannick and Vidal, Vanessa and Lours, Philippe. Processing, repairing and cyclic oxidation behaviour of sol–gel thermal barrier coatings. (2011) Surface and Coatings Technology, vol. 206 (n° 7). pp. 1609-1614. ISSN 0257-8972

Gourc, Etienne and Seguy, Sébastien and Arnaud, Lionel. Chatter milling modeling of active magnetic bearing spindle in high-speed domain. (2011) International Journal of Machine Tools and Manufacture, vol. 51 (n° 12). pp. 928-936. ISSN 0890-6955

Gouache, Thibault and Brunskill, Christopher and Scott, Gregory and Gao, Yang and Coste, Pierre and Gourinat, Yves. Regolith simulant preparation methods for hardware testing. (2011) Planetary and Space Science, vol. 58 (n° 14-15). pp. 1977-1984. ISSN 0032-0633

Cazajus, Vincent and Seguy, Sébastien and Welemane, Hélène and Karama, Moussa. Residual stresses in a ceramic-metal composite. (2011) Applied Mechanics and Materials, vol. 146. pp. 185-196. ISSN 1662-7482

Tadier, Solène and Le Bolay, Nadine and Girod Fullana, Sophie and Cazalbou, Sophie and Charvillat, Cédric and Labarrère, Michel and Boitel, Daniel and Rey, Christian and Combes, Christèle. Co-grinding significance for calcium carbonate-calcium phosphate mixed cement. Part II: effect on cement properties. (2011) Journal of Biomedical Materials Research Part B: Applied Biomaterials, vol. 99B (n° 2). pp. 302-312. ISSN 1552-4973

Pozzolini, Cédric and Salaün, Michel. Some energy conservative schemes for vibro-impacts of a beam on rigid obstacles. (2011) ESAIM: Mathematical Modelling and Numerical Analysis, vol. 45 (n° 6). pp. 1163-1192. ISSN 0764-583X

Sanches, Leonardo and Michon, Guilhem and Berlioz, Alain and Alazard, Daniel. Instability zones for isotropic and anisotropic multibladed rotor configurations. (2011) Mechanism and Machine Theory, vol. 46 (n° 8). pp. 1054-1065 . ISSN 0094-114X

Perret, Adrien and Mistou, Sébastien and Denaud, Louis Etienne and Mollé, Thierry and Veyrac, Claudia and Karama, Moussa. Numerical modelling of a composite fuselage manufactured by liquid resin infusion. (2011) Applied Mechanics and Materials, vol. 62. pp.49-56. ISSN 1662-7482

Shad, Rizwan and Michon, Guilhem and Berlioz, Alain. Modeling and analysis of nonlinear rotordynamics due to higher order deformations in bending. (2011) Applied Mathematical Modelling, vol. 35 (n° 5). pp. 2145-2159 . ISSN 0307-904X

Péronnet, Elodie and Eyma, Florent and Pastor, Marie-Laetitia and Welemane, Hélène. Caractérisation et comparaison des limites de détection de techniques de contrôle non destructif : méthodes ultrasonores et méthodes optiques. (2011) Contrôles-Essais-Mesures, Vol. 37. pp. 63-68. ISSN 1637-4657

Campa, Francisco Javier and López de Lacalle, Luis Norberto and Urbicain, Gorka and Lamikiz, Aitzol and Seguy, Sébastien and Arnaud, Lionel. Critical thickness and dynamic stiffness for chatter avoidance in thin floors milling. (2011) Advanced Materials Research, vol. 188. pp. 116-121. ISSN 1662-8985

Le Bot, Alain and Bou-Chakra, Elie and Michon, Guilhem. Dissipation of vibration in rough contact. (2011) Tribology Letters, vol. 41 (n° 1). pp. 47-53. ISSN 1023-8883

Gourc, Etienne and Seguy, Sébastien and Dessein, Gilles. Dynamical modeling of spindle with active magnetic bearing for milling process. (2011) Advanced Materials Research, vol. 423. pp. 200-209. ISSN 1662-8985

Bizeul, Matthieu and Bouvet, Christophe and Barrau, Jean-Jacques and Cuenca, Rémy. Fatigue crack growth in thin notched woven glass composites under tensile loading. Part I: experimental. (2011) Composites Science and Technology, vol. 71 (n° 3). pp. 289-296. ISSN 0266-3538

Bizeul, Matthieu and Bouvet, Christophe and Barrau, Jean-Jacques and Cuenca, Rémy. Fatigue crack growth in thin notched woven glass composites under tensile loading. Part II: modelling. (2011) Composites Science and Technology, vol. 71 (n° 3). pp. 297-305. ISSN 0266-3538

Limido, Jérôme and Espinosa, Christine and Salaün, Michel and Mabru, Catherine and Chieragatti, Rémy and Lacome, Jean-Luc. Metal cutting modelling SPH approach. (2011) International Journal of Machining and Machinability of Materials, vol. 9 (n° 3-4). pp. 177-196. ISSN 1748-5711

Arnaud, Lionel and Gonzalo, Oscar and Seguy, Sébastien and Jauregi, Haritz and Peigné, Grégoire. Simulation of low rigidity part machining applied to thin-walled structures. (2011) The International Journal of Advanced Manufacturing Technology, vol. 54 (n° 5-8). pp. 479-488. ISSN 0268-3768

Seguy, Sébastien and Insperger, Tamás and Arnaud, Lionel and Dessein, Gilles and Peigné, Grégoire. Suppression of period doubling chetter in high-speed milling by spindle speed variation. (2011) Machining Science and Technology, vol. 15 (n° 2). pp. 153-171. ISSN 1091-0344

Shahzad, Majid and Chaussumier, Michel and Chieragatti, Rémy and Mabru, Catherine and Rezaï-Aria, Farhad. Surface characterization and influence of anodizing process on fatigue life of Al 7050 alloy. (2011) Materials & Design, vol. 32 (n° 6). pp. 3328-3335 . ISSN 0261-3069

Garnier, Christian and Pastor, Marie-Laetitia and Eyma, Florent and Lorrain, Bernard. The detection of aeronautical defects in-situ on composite structures using Non Destructive Testing. (2011) Composite Structures, vol. 93. pp. 1328-1336. ISSN 0263-8223

Ledru, Yohann and Bernhart, Gérard and Piquet, Robert and Schmidt, Fabrice and Michel, Laurent. Coupled visco-mechanical and diffusion void growth modelling during composite curing. (2010) Composites Science and Technology, vol. 70 (n° 15). pp. 2139-2145. ISSN 0266-3538

Goueffon, Yann and Mabru, Catherine and Labarrère, Michel and Arurault, Laurent and Tonon, Claire and Guigue, Pascale. Investigations into the coefficient of thermal expansion of porous films prepared on AA7175 T7351 by anodizing in sulphuric acid electrolyte. (2010) Surface and Coatings Technology, vol. 205 (n° 7). pp. 2643-2648. ISSN 0257-8972

Sniezewski, Julien and LeMaoult, Yannick and Lours, Philippe and Pin, Lisa and Menvie Bekale, Vincent and Monceau, Daniel and Oquab, Djar and Fenech, Justine and Ansart, Florence and Bonino, Jean-Pierre. Sol–gel thermal barrier coatings: Optimization of the manufacturing route and durability under cyclic oxidation. (2010) Surface and Coatings Technology, vol. 205 (n° 5). pp. 1256-1261. ISSN 0257-8972

Shahzad, Majid and Chaussumier, Michel and Chieragatti, Rémy and Mabru, Catherine and Rezaï-Aria, Farhad. Influence of surface treatments on fatigue life of Al 7010 alloy. (2010) Journal of Materials Processing Technology, vol. 210 (n° 13). pp. 1821-1826. ISSN 0924-0136

Pastor, Marie-Laetitia and Garnier, Christian and Pescay, Christophe. Comparison of two non destructive tests in carbon/epoxy composites. (2010) Journal of Materials Science and Engineering, vol. 4 (n° 10). ISSN 1934-8959

Seguy, Sébastien and Insperger, Tamás and Arnaud, Lionel and Dessein, Gilles and Peigné, Grégoire. On the stability of high-speed milling with spindle speed variation. (2010) The International Journal of Advanced Manufacturing Technology, vol. 48 (n° 9-12). pp. 883-895. ISSN 0268-3768

Chaussumier, Michel and Shahzad, Majid and Mabru, Catherine and Chieragatti, Rémy and Rezaï-Aria, Farhad. A fatigue multi-site cracks model using coalescence, short and long crack growth laws, for anodized aluminum alloys. (2010) Procedia Engineering, vol. 2 (n° 1). pp. 995-1004. ISSN 1877-7058

Shahzad, Majid and Chaussumier, Michel and Chieragatti, Rémy and Mabru, Catherine and Rezaï-Aria, Farhad. Influence of anodizing process on fatigue life of a machined aluminium alloy. (2010) Procedia Engineering, vol. 2 (n° 1). pp. 1015-1024. ISSN 1877-7058

Weiss, Ambrosius and Trabelsi, Walid and Michel, Laurent and Barrau, Jean-Jacques and Mahdi, Stephane. Influence of ply-drop location on the fatigue behaviour of tapered composites laminates. (2010) Procedia Engineering, vol. 2 (n° 1). pp. 1105-1114. ISSN 1877-7058

Shah, Masood and Mabru, Catherine and Rezaï-Aria, Farhad. Investigation of crack propagation in X38CrMoV5 (AISI H11) tool steel at elevated temperatures. (2010) Procedia Engineering, vol. 2 (n° 1). pp. 2045-2054. ISSN 1877-7058

Goueffon, Yann and Mabru, Catherine and Labarrère, Michel and Arurault, Laurent and Tonon, Claire and Guigue, Pascale. Mechanical behaviour of black anodic films on 7175 aluminium alloy for space applications. (2010) Metal Finishing, vol. 108 (n° 2). pp. 22-27. ISSN 0026-0576

Seguy, Sébastien and Dessein, Gilles and Arnaud, Lionel and Insperger, Tamás. Control of chatter by spindle speed variation in high-speed milling. (2010) Advanced Materials Research, Vol. 112. pp.179-186. ISSN 1022-6680

Trabelsi, Walid and Michel, Laurent and Othomene, Renaud. Effects of stitching on delamination of satin weave carbon-epoxy laminates under mode I, mode II and mixed-mode I/II loadings. (2010) Applied Composite Materials, vol. 17 (n° 6). pp. 575-595. ISSN 0929-189X

Bizeul, Matthieu and Bouvet, Christophe and Barrau, Jean-Jacques and Cuenca, Rémy. Influence of woven ply degradation on fatigue crack growth in thin notched composites under tensile loading. (2010) International Journal of Fatigue, vol. 32 (n° 1). pp. 60-65. ISSN 0142-1123

Mezeix, Laurent and Bouvet, Christophe and Huez, Julitte and Poquillon, Dominique. Mechanical behavior of entangled fibers and entangled cross-linked fibers during compression. (2009) Journal of Materials Science, vol. 44 (n° 14). pp. 3652-3661. ISSN 0022-2461

Bouvet, Christophe and Castanié, Bruno and Bizeul, Matthieu and Barrau, Jean-Jacques. Low velocity impact modelling in laminate composite panels with discrete interface elements. (2009) International Journal of Solids and Structures, vol. 46 (n° 14-15). pp. 2809-2821. ISSN 0020-7683

Castanié, Bruno and Aminanda, Yulfian and Bouvet, Christophe and Barrau, Jean-Jacques. Core crush criterion to determine the strength of sandwich composite structures subjected to compression after impact. (2008) Composite Structures, vol. 8 (n° 1-3). pp. 243-250. ISSN 0263-8223

Castanié, Bruno and Bouvet, Christophe and Aminanda, Yulfian and Barrau, Jean-Jacques and Thévenet, Pascal. Modelling of low-energy/low-velocity impact on Nomex honeycomb sandwich structures with metallic skins. (2008) International Journal of Impact Engineering, vol. 3 (n° 7). pp. 620-634. ISSN 0734-743X

Petit, Sandrine and Bouvet, Christophe and Bergerot, Alain and Barrau, Jean-Jacques. Impact and compression after impact experimental study of a composite laminate with a cork thermal shield. (2007) Composites Science and Technology, vol. 6 (n° 15-). pp. 3286-3299 . ISSN 0266-3538

Gourinat, Yves and Salem , Amgad. L’amortissement dynamique non-destructif au sein des matériaux structuraux. (2001) Sciences, vol. 3. pp. 57-65. ISSN 0151-0304

Conference or Workshop Item

Jaillon, Agathe and Jumel, Julien and Lachaud, Frédéric and Paroissien, Eric and Renart, Jordi. Thickness influence on a structural methacrylate adhesive behavior. (2018) In: 6th World Congress on Adhesion and Related Phenomena (WCARP 2017), 25 February 2018 - 1 March 2018 (San Diego, United States). (Unpublished)

Barus, Matthias and Welemane, Hélène and Nassiet, Valérie and Pastor, Marie-Laetitia and Cantarel, Arthur and Collombet, Francis and Crouzeix, Laurent and Grunevald, Yves-Henri. Analyse de réparations collées par thermographie InfraRouge : optimisation de la réponse thermique du joint structural. (2017) In: GDR week du GDR CNRS 3671 MIC, 14 November 2017 - 17 November 2017 (Talence, France). (Unpublished)

Serrano, Léonard and Olivier, Philippe and Cinquin, Jacques. Compaction behavior of out-of-autoclave prepreg materials. (2017) In: ESAFORM 2017 (20th International Conference on Forming), 26 April 2017 - 28 April 2017 (Dublin, Ireland).

Barus, Matthias and Welemane, Hélène and Collombet, Francis and Nassiet, Valérie and Pastor, Marie-Laetitia and Cantarel, Arthur and Crouzeix, Laurent and Grunevald, Yves-Henri. Comportement thermique d'un joint de colle structural et analyse par thermographie infrarouge : application à la caractérisation de structures composites réparées. (2017) In: Colloque francophone CMOI-FLUVISU, 20 March 2017 - 24 March 2017 (Le Mans, France). (Unpublished)

Hirschler, Thibaut and Bouclier, Robin and Duval, Arnaud and Crozes, Damien and Elguedj, Thomas and Morlier, Joseph. Analyse Isogéométrique pour les problèmes d’Optimisation de Forme des Structures Coques. (2017) In: 13eme Colloque National en Calcul des Structures (CSMA 2017), 15 May 2017 - 19 May 2017 (Giens, France).

Rouset, Pierrick and Budinger, Marc and Pommier-Budinger, Valérie. Comparison of extensional and flexural modes for the design of piezoelectric ice protection systems. (2017) In: 7th European Conference for Aeronautics and Space Sciences (EUCASS), 3 July 2017 - 6 July 2017 (Milan, Italy).

Toniolli, Mateus and Bouclier, Robin and Guinard, Stéphane and Passieux, Jean-Charles. Couplage non-intrusif d’un modèle global coque et de modèles locaux solides 3D non-linéaires pour la simulation d’aérostructures. (2017) In: 13eme Colloque National en Calcul des Structures (CSMA 2017), 15 May 2017 - 19 May 2017 (Giens, France).

Chiplunkar, Ankit and Bosco, Elisa and Morlier, Joseph. Gaussian Process for Aerodynamic Pressures Prediction in Fast Fluid Structure Interaction Simulations. (2017) In: 12th World Congress on Structural and Multidisciplinary Optimization, 5 June 2017 - 7 June 2017 (Braunschweig, Germany).

Barjhoux, Pierre-Jean and Diouane, Youssef and Grihon, Stéphane and Bettebghor, Dimitri and Morlier, Joseph. Mixed Variable Structural Optimization: Toward an Efficient Hybrid Algorithm. (2017) In: 12th World Congress on Structural and Multidisciplinary Optimisation, 5 June 2017 - 9 June 2017 (Braunschweig, Germany).

Aufray, Maëlenn and Paroissien, Eric and Sauvage, Jean-Baptiste and Poquillon, Dominique and Lachaud, Frédéric. Modélisation expérimentale et numérique de l’essai de flexion 3 points. (2017) In: 19è Journées d'études sur l'adhésion (JADH 2017), 8 October 2017 - 13 October 2017 (Saint-Maxime, France). (Unpublished)

Chiplunkar, Ankit and Morlier, Joseph. Operational Modal Analysis in Frequency Domain using Gaussian Mixture Models. (2017) In: The 35th International Modal Analysis Conference (IMAC XXXV),, 30 January 2017 - 2 February 2017 (Los Angeles, United States).

Bakrani Balani, Shahriar and Chabert, France and Nassiet, Valérie and Cantarel, Arthur and Garnier, Christian. Toward improvement of the properties of parts manufactured by FFF ( Fused Filament Fabrication) through understanding the influence of temperature and rheological behaviour on the coalescence phenomenon. (2017) In: ESAFORM 2017, 26 April 2017 - 28 April 2017 (Dublin, Ireland).

Rouset, Pierrick and Budinger, Marc and Pommier-Budinger, Valérie. Ultrasonic ice protection systems. (2017) In: More Electric Aircraft - MEA 2017, 1 February 2017 - 2 February 2017 (Bordeaux, France). (Unpublished)

Bouclier, Robin and Passieux, Jean-Charles and Périé, Jean-Noel. Une méthode de couplage de domaines pour la mesure de champs par corrélation d’images numériques éléments finis. (2017) In: CSMA 2017 - 13ème Colloque National en Calcul des Structures, 15 May 2017 - 19 May 2017 (Giens, France).

Dubreuil, Sylvain and Mas-Colomer, Juan and Salaün, Michel and Bartoli, Nathalie and Lefebvre, Thierry. Évaluation de l’incertitude associée à l’interpolation de maillage dans un calcul couplé partitionné. (2017) In: 13eme Colloque National en Calcul des Structures (CSMA 2017), 15 May 2017 - 19 May 2017 (Giens, France).

Barus, Matthias and Welemane, Hélène and Collombet, Francis and Pastor, Marie-Laetitia and Cantarel, Arthur and Nassiet, Valérie and Crouzeix, Laurent and Grunevald, Yves-Henri. A New NDT Method for the study of composite bonded repair. (2016) In: 17th European Conference on Composite Materials - ECCM17, 26 June 2016 - 30 June 2016 (Munich, Germany).

Pommier-Budinger, Valérie and Budinger, Marc and Tepylo, Nick and Huang, Xiao. Analysis of piezoelectric ice protection systems combined with ice-phobic coatings. (2016) In: 8th AIAA Atmospheric and Space Environments Conference, AIAA AVIATION Forum, 13 June 2016 - 17 June 2016 (Washington, United States).

Pommier-Budinger, Valérie and Bury, Yannick and Michon, Guilhem and Napias, Gael. In-flight piv for cror flight test demonstration. (2016) In: 32nd AIAA Aerodynamic Measurement Technology and Ground Testing Conference, AIAA AVIATION Forum, 6 June 2016 - 11 June 2016 (Washington, United States).

Martineau, Lilian and Chabert, France and Bernhart, Gérard and Djilali, Toufik. Mechanical behavior of amorphous PEEK in the rubbery state. ( In Press: 2016) In: ECCM17 - 17th European Conference on Composite Materials, 26 June 2016 - 30 June 2016 (Munich, Germany).

Barriere, Ludovic and Cherrier, Olivier and Passieux, Jean-Charles and Bouquet, Michel and Ferrero, Jean-François. 3D digital image correlation applied to birdstrike tests. (2016) In: iDICS 2016 (International DIC Society), 7 November 2016 - 10 November 2016 (Philadelphia, United States).

Chiplunkar, Ankit and Rachelson, Emmanuel and Colombo, Michele and Morlier, Joseph. Adding Flight Mechanics to Flight Loads Surrogate Model using Multi-Output Gaussian Processes. (2016) In: 17th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, AIAA AVIATION Forum, 13 June 2016 - 17 June 2016 (Washington, United States).

Thauvin, Jérome and Barraud, Guillaume and Roboam, Xavier and Sareni, Bruno and Budinger, Marc and Leray, Dimitri. Hybrid Propulsion for Regional Aircraft: a Comparative Analysis based on Energy Efficiency. ( In Press: 2016) In: ESARS-ITEC 2016, 2 November 2016 - 4 November 2016 (Toulouse, France).

Thauvin, Jérome and Barraud, Guillaume and Budinger, Marc and Leray, Dimitri and Roboam, Xavier and Sareni, Bruno. Hybrid Regional Aircraft: A Comparative Review of New Potentials Enabled by Electric Power. (2016) In: 52nd AIAA/SAE/ASEE Joint Propulsion Conference, 25 July 2016 - 27 July 2016 (Salt Lake City, United States).

Chiplunkar, Ankit and Rachelson, Emmanuel and Colombo, Michele and Morlier, Joseph. Identification of Physical Parameters Using Change-Point Kernels. (2016) In: SIAM Uncertainty Quantification 2016, 5 April 2016 - 8 April 2016 (Lausanne, Switzerland).

Pons Lelardeux, Catherine and Panzoli, David and Lagarrigue, Pierre and Jessel, Jean-Pierre. Making Decisions in a Virtual Operating Room. (2016) In: 17th International Conference on Collaboration Technologies and Systems (CTS 2016), 31 October 2016 - 4 November 2016 (Orlando, United States).

Chiplunkar, Ankit and Rachelson, Emmanuel and Colombo, Michele and Morlier, Joseph. Sparse Physics-based Gaussian Process for Multi-output Regression using Variational Inference. (2016) In: International Conference on Pattern Recognition Applications and Methods, 24 February 2016 - 26 February 2016 (Rome, Italy).

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Identification of damage mechanisms in CFRP composites by coupling acoustic emission and infrared thermography. (2015) In: Franco-Chinese Symposium on Damage and Francture of Composite Structures : Assesment and Monitoring, 14 July 2015 - 17 July 2015 (Tarbes, France). (Unpublished)

Duval, Mickaël and Passieux, Jean-Charles and Salaün, Michel. Couplage non-intrusif: réanalyse locale et calcul haute performance. (2015) In: CSMA 2015 - 12ème Colloque National en Calcul des Structures, 18 May 2015 - 22 May 2015 (Giens (Var), France). (Unpublished)

Bouclier, Robin and Passieux, Jean-Charles and Salaün, Michel and Laborde, Patrick. Enrichissement local de modèles NURBS par couplage non intrusif avec des éléments finis classiques. (2015) In: CSMA 2015 - 12e Colloque National en Calcul des Structures, 18 May 2015 - 22 May 2015 (Giens (Var), France). (Unpublished)

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Identification de mécanismes d’endommagement de stratifiés carbone/époxy par couplage entre émission acoustique et thermographie infrarouge. (2015) In: Journée Scientifique et Technique, 12 March 2015 - 13 March 2015 (Cachan, France). (Unpublished)

Michetti, Jérôme and Basarab, Adrian and Tran, Michel and Diemer, Franck and Kouamé, Denis. Cone-Beam Computed Tomography contrast validation of an artificial periodontal phantom for use in endodontics. (2015) In: 37th Annual International Conference of the IEEE Engineering in Medicine and Biology Society (EMBC 2015), 25 August 2015 - 29 August 2015 (Milano, Italy).

Barus, Matthias and Collombet, Francis and Welemane, Hélène and Crouzeix, Laurent and Cantarel, Arthur and Grunevald, Yves-Henri and Nassiet, Valérie and Pastor, Marie-Laetitia. Infrared signatures of bonded interfaces for the repair of primary structures in composite materials. (2015) In: 20th International Conference on Composite Materials, 19 July 2015 - 24 July 2015 (Copenhague, Denmark).

Paroissien, Eric and Da Veiga, Anthony and Schwartz, Sébastien and Lélias, Guillaume and Lachaud, Frédéric and Meyer, Pierre-Yves. Simplified stress analysis of bonded joints using the macro-element technique. (2015) In: Forum TERATEC 2015, 23 June 2015 - 24 June 2015 (Palaiseau, France). (Unpublished)

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Identification de mécanismes d'endommagement de stratifiés carbone-époxy par émission acoustique. (2014) In: Journée CILSA (Classification, Identification et Localisation de Sources Acoustiques), 18 September 2014 - 18 September 2014 (Lyon, France). (Unpublished)

Munoz Cuartas, Victor and Vales, Benjamin and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Coupling infrared thermography and acoustic emission for damage study in CFRP composites. (2014) In: The 12th International Conference on Quantitative InfraRed Thermography - QIRT 2014, 7 July 2014 - 11 July 2014 (Bordeaux, France).

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Identification of the elastic properties in CFRP composites. (2014) In: International Symposium on Aircraft Materials ACMA 2014, 23 April 2014 - 26 April 2014 (Marrakech, Morocco).

Duval, Mickaël and Passieux, Jean-Charles and Salaün, Michel and Guinard, Stéphane. Local/global non-intrusive parallel coupling for large scale mechanical analysis. (2014) In: 11th World Congress on Computational Mechanics - 5th European Conference on Computational Mechanics. IACM-ECCOMAS, 20 July 2014 - 25 July 2014 (Barcelone, Spain).

Duval, Mickaël and Passieux, Jean-Charles and Salaün, Michel and Guinard, Stéphane. Non-Intrusive model coupling: A flexible way to handle local geometric and mechanical details in FEA. ( In Press: 2014) In: Joint conference on Mechanical, Design Engineering & Advanced Manufacturing, 18 June 2014 - 20 June 2014 (Toulouse, France).

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Utilisation de la thermographie infrarouge et de l'émission acoustique pour l'identification de l'endommagement d'un composite stratifié carbone-époxy. (2014) In: VIIIèmes Journées d’Etudes Techniques - International congress for applied mechanics JET 2014, 28 April 2014 - 30 April 2014 (Marrakech, Morocco).

Ferraioli, Giuseppe and Causse, Mickaël and Lizy-Destrez, Stéphanie and Gourinat, Yves. Habitability of manned vehicules : the impact of human factors on future long duration human space exploration missions en route to Mars. (2013) In: Proceedings of 64th International Astronautical Congress, Beijing, China, September 23-27, 2013, 2013 - 2013 (Beijing, China).

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Application of non destructive testing to the detection of aeronautical defects in composite structures. (2013) In: International Conference of Nonconventional Technologies, 12 June 2013 - 15 June 2013 (Sibiu, Romania).

Busca, Damien and Fazzini, Marina and Lorrain, Bernard and Mistou, Sébastien and Karama, Moussa and Pastor, Marie-Laetitia. High-Speed digital image correlation : application to bi-axial fatigue. (2013) In: 17th International Conference on Composite Structures - ICCS17(2013), 17 June 2013 - 21 June 2013 (Porto, Portugal). (Unpublished)

Busca, Damien and Fazzini, Marina and Lorrain, Bernard and Mistou, Sébastien and Karama, Moussa and Pastor, Marie-Laetitia. High-speed digital image correlation: application to bi-axial fatigue. (2013) In: PhotoMechanics 2013, 27 May 2013 - 29 May 2013 (Montpellier, France). (Unpublished)

Péronnet, Elodie and Pastor, Marie-Laetitia and Welemane, Hélène and Huillery, Richard . Non destructive testing of artificial defects in composite structures by thermal full field measurement methods. (2013) In: PhotoMechanics 2013, 27 May 2013 - 29 May 2013 (Montpellier, France). (Unpublished)

Wang, Xuan and Reysset, Aurélien and Pommier-Budinger, Valérie and Gourinat, Yves. A Modified Preisach Model for Hysteresis in Piezoelectric Actuators. (2013) In: 11th International Workshop of Electronics, Control, Measurement, Signals & application to Mechatronics (ECMSM), 24 June 2013 - 26 June 2013 (Toulouse, France).

Dubreuil, Sylvain and Petitjean, Frank and Salaün, Michel. A coupled parametric and nonparametric approach for modal analysis of a satellite. (2013) In: ICOSSAR 2013, 11th International Conference on Structural Safety and Reliability, 16 June 2013 - 20 June 2013 (New York, United States).

Lv, Peng and Mohd Zawawi, Fazila and Bénard, Emmanuel and Prothin, Sebastien and Moschetta, Jean-Marc and Morlier, Joseph. Adaptive proprotors as applied to convertible MAVs. (2013) In: International Micro Air Vehicle Conference and Flight Competition (IMAV2013) , 17 September 2013 - 20 September 2013 (Toulouse, France).

Lachaud, Frédéric and Piquet, Robert and Paroissien, Eric and Huet, Jacques. Approche couplée essais-calculs pour l’analyse du comportement des assemblages boulonnés en composites stratifiés. (2013) In: NAFEMS, 30 May 2013 (Paris, France). (Unpublished)

Gontier, Justine and Hervas Garcia, Carlos and Bordeneuve-Guibé, Joël and Espinosa, Christine. CANSAT: Multiphysical experimental design of a probe come-back mission. (2013) In: 64th IAC - International Astronautical Congress, 23 September 2013 - 27 September 2013 (Beijing, China).

Dubreuil, Sylvain and Petitjean, Frank and Salaün, Michel. Etude numérique de l'influence de la structure de dépendance des valeurs propres en synthèse modale probabiliste. (2013) In: CFM 2013 - 21ème Congrès Français de Mécanique, 26-30 Aug 2013, Bordeaux, France . (Unpublished)

Munoz Cuartas, Victor and Perrin, Marianne and Pastor, Marie-Laetitia and Welemane, Hélène and Cantarel, Arthur and Karama, Moussa. Identification of the elastic properties of composite materials. (2013) In: International Conference on Structural Analysis of Advanced Materials, 23 September 2013 - 26 September 2013 (Island of Kos, Greece). (Unpublished)

Pozzolini, Cédric and Renard, Yves and Salaün, Michel. Schémas asymptotiquement conservatifs en énergie dans un problème de vibro-impact de plaques. (2013) In: CSMA 2013 - 11ème Colloque National en Calcul des Structures, 13-17 May 2013, Giens, France .

Lv, Peng and Prothin, Sebastien and Mohd Zawawi, Fazila and Bénard, Emmanuel and Morlier, Joseph and Moschetta, Jean-Marc. Study of A Flexible Blade for Optimized Proprotor. (2013) In: ERCOFTAC International symposium Unsteady separation in fluid-structure interaction, 17 June 2013 - 21 June 2013 (Mykonos, Greece).

Mohd Zawawi, Fazila and Prothin, Sebastien and Lv, Peng and Bénard, Emmanuel and Moschetta, Jean-Marc and Morlier, Joseph. Study of a Flexible UAV Proprotor. (2013) In: 48th International Symposium of Applied Aerodynamics , 25 March 2013 - 27 March 2013 (Saint-Louis, France).

Busca, Damien and Fazzini, Marina and Lorrain, Bernard and Mistou, Sébastien and Karama, Moussa and Pastor, Marie-Laetitia. Suivi d’essais de fatigue bi-axiale sur des composites stratifiés. (2013) In: 13ème colloque international francophone sur les "Méthodes et Techniques Optiques pour l'Industrie" - CMOI2013, 18 November 2013 - 22 November 2013 (Orléans, France).

Dubreuil, Sylvain and Petitjean, Frank and Salaün, Michel. Synthèse modale probabiliste de systèmes à plusieurs degrés de liberté. (2013) In: CSMA 2013 - 11ème Colloque National en Calcul des Structures, 13-17 May 2013, Giens, France .

Jaeger, Laure and Jorquera, Tom and Lemouzy, Sylvain and Gogu, Christian and Segonds, Stéphane and Bes, Christian. Uncertainty propagation in multi-agent systems for multidisciplinary optimization problems. (2013) In: 10th World Congress on Structural and Multidisciplinary Optimization (WCSMO 10), 19 May 2013 - 24 May 2013 (Orlando, Florida, United States).

Wang, Xuan and Pommier-Budinger, Valérie and Gourinat, Yves. A Specific Methodology of Creep Compensation for piezoelectric Actuators by Open-loop control. ( In Press: 2012) In: International Conference on Mechanical Engineering, Materials and Energy (ICMEME 2012), 26 October 2012 - 27 October 2012 (Dalian, China).

Vieille, Benoit and Casado, Victor Manuel and Bouvet, Christophe. Comparative study on the impact behavior and damage tolerance of woven carbon fiber reinforced thermoplastic– and thermosetting– composites. (2012) In: ECCM15 - 15th European conference on composite materials, 24-28 June 2012, Venice, Italy .

Dubreuil, Sylvain and Berveiller, Marc and Petitjean, Frank and Salaün, Michel. Determination of Bootstrap confidence intervals on sensitivity indices obtained by polynomial chaos expansion. (2012) In: JFMS12 - Journées Fiabilité des Matériaux et des Structures, 04-06 Jun 2012, Chambéry, France .

Péronnet, Elodie and Pastor, Marie-Laetitia and Huillery, Richard and Dalverny, Olivier and Mistou, Sébastien and Welemane, Hélène. Non destructive investigation of defects in composite structures by three infrared thermographic techniques. (2012) In: International conference on experimental mechanics ICEM 15, 22 July 2012 - 27 July 2012 (Porto, Portugal).

Ben Slima, Khalil and Penazzi, Luc and Mabru, Catherine and Ronde-Oustau, François and Rezaï-Aria, Farhad. A new method for advanced virtual design of stamping tools for automotive industry: application to nodular cast iron EN-GJS-600-3. (2011) In: The 14th International Conference on Material Forming - ESAFORM 2011, 27-29 April 2011, Belfast, UK .

Garnier, Christian and Pastor, Marie-Laetitia and Lorrain, Bernard. Finite element model for impact on composite structures. (2011) In: 16th International Conference on Composite Structures , 28 June 2011 - 28 June 2011 (Porto, Portugal).

Roussouly, Nicolas and Petitjean, Frank and Salaün, Michel. Analyse de la fiabilité d’une structure spatiale. (2011) In: CSMA 2011 - 10ème Colloque National en Calcul des Structures, 09-13 May 2011, Giens, France .

Morlier, Joseph and Bettebghor, Dimitri. Compressed sensing applied to modeshapes reconstruction. (2011) In: IMAC XXX Conference and exposition on structural dynamics, 30 Jan – 02 Feb 2012, Jacksonville, USA . (Unpublished)

Gourc, Etienne and Michon, Guilhem and Seguy, Sébastien and Berlioz, Alain. Experimental investigation and theoretical analysis of a nonlinear energy sink under harmonic forcing. (2011) In: ASME 2011 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, 28-31 August 2011, Washington, USA .

Israr, Haris Ahmad and Rivallant, Samuel and Zeng, Huabin and Barrau, Jean-Jacques. Finite element modelling of CFRP plates under crushing. (2011) In: 18th International Conference on Composite Materials - ICCM 18 , 21-26 Aug 2011, Jeju Island, Korea .

Foucaud, Simon and Michon, Guilhem and Morlier, Joseph and Gourinat, Yves. Harmonic response of the organ of corti: results for wave dispersion. (2011) In: The 11th International Mechanics of Hearing Workshop, 16–22 Jul 2011, Williamstown, USA .

Kolopp, Amélie and Rivallant, Samuel and Bouvet, Christophe. Impact sur structures sandwich composites pour application de blindage aéronautique. (2011) In: JNC 17 - 17èmes Journées Nationales sur les Composites, 15-17 juin 2011, Poitiers, France .

Coquet, Yves and Bordeneuve, Pascal and Capmas, Guillaume and Espinosa, Christine. Improvements in Fluid Structure Interaction simulations of LS-Dyna(r). (2011) In: 21st AIAA Aerodynamic Decelerator Systems Technology Conference and Seminar, 23 May 2011 - 26 May 2011 (Dublin, Ireland).

Morlier, Joseph and Bergh, Mauricio and Mevel, Laurent. Modeshapes recognition using Fourier descriptors: a simple SHM example. (2011) In: IMAC XXX Conference and exposition on structural dynamics, 30 Jan – 02 Feb 2012, Jacksonville, USA . (Unpublished)

Pozzolini, Cédric and Renard, Yves and Salaün, Michel. Schémas numériques conservatifs pour des problèmes de vibro-impacts de poutres et de plaques. (2011) In: CSMA 2011 - 10ème Colloque National en Calcul des Structures, 09-13 May 2011, Giens, France .

Paroissien, Eric and Campassens, Denis. Stress analysis support to structural sealant development. (2011) In: 14th Numerical Simulation Meeting, HUTCHINSON, June 2011 (Cernay-la-ville, France). (Unpublished)

Roussouly, Nicolas and Petitjean, Frank and Salaün, Michel and Buffe, Fabrice and Carpine, Anne. Application des surfaces de réponse pour l’analyse fiabiliste d’une structure spatiale. (2010) In: JFMS10 - Journées Fiabilité des Matériaux et des Structures, 24-26 Mar 2010, Toulouse, France .

Marger, Thibaut and Pommier-Budinger, Valérie and Maré, Jean-Charles and Malburet, François. Designing redundant metering valves for hydraulic actuators under mixability and low cost-constraints. (2010) In: 10th AIAA Aviation Technology, Integration, and Operations (ATIO) Conference, 13-15 Sept 2010, Fort Worth, United States .

Chieragatti, Rémy and Espinosa, Christine and Lacome, Jean-Luc and Limido, Jérôme and Mabru, Catherine and Salaün, Michel. Détermination d’un Kt local associé à la rugosité de surface ; influence sur la tenue en fatigue. (2010) In: 29èmes journées de printemps de la SF2M "Influence des procédés sur la tenue en fatigue, rôle des défauts", 19-20 May 2010, Paris .

Garnier, Christian and Lorrain, Bernard and Pastor, Marie-Laetitia. Impact damage evolution under fatigue loading by InfraRed Thermography on composite structures. (2010) In: 14th International Conference of Experimental Mechanics (ICEM 14), 4 July 2010 - 9 July 2010 (Poitiers, France).

Weiss, Ambrosius and Trabelsi, Walid and Michel, Laurent and Barrau, Jean-Jacques and Mahdi, Stephane. Influence of ply-drop location on the fatigue behaviour of tapered composites laminates. (2010) In: 10th International Fatigue Congress, 6 June 2010 - 11 June 2010 (Prague, Czech Republic).

Duong, Anh Vu and Rivallant, Samuel and Barrau, Jean-Jacques and Petiot, Caroline and Malherbe, Benoît. Influence of speed on the crushing behavior of composite plates. (2010) In: ACCM 7 – 7th Asian-Australasian Conference on Composite Materials, 15-18 Nov 2010, Taipei, Taiwan .

Sanches, Leonardo and Michon, Guilhem and Berlioz, Alain and Alazard, Daniel. Instability zones for isotropic and anisotropic multiblades rotor configurations. (2010) In: 17ème conférence Vibrations, Chocs et Bruits 2010, 15-17 Juin 2010, Ecully, France . (Unpublished)

Sanches, Leonardo and Michon, Guilhem and Berlioz, Alain and Alazard, Daniel. Instability zones identification in multiblade rotor dynamics. (2010) In: 11th Pan-American Congress of Applied Mechanics, 04-08 Jan 2010, Foz do Iguaçu, Brazil .

Rahmé, Pierre and Bouvet, Christophe and Rivallant, Samuel and Fascio, Valia and Valembois, Guy. Mechanical protection for composite structures submitted to low energy impact. (2010) In: ECCM14 - 14th European Conference on Composite Materials, 7 June 2010 - 10 June 2010 (Budapest, Hungary).

Bouvet, Christophe and Rivallant, Samuel and Barrau, Jean-Jacques. Modelling of impact damage and permanent indentation on laminate composite plate. (2010) In: ECCM14 - 14th European Conference on Composite Materials, 7 June 2010 - 10 June 2010 (Budapest, Hungary).

Chaussumier, Michel and Shahzad, Majid and Mabru, Catherine and Chieragatti, Rémy and Rezaï-Aria, Farhad. Modélisation de la multi-fissuration d’un alliage d’aluminium 7010 traité par oxydation anodique chromique. (2010) In: 29èmes journées de Printemps de la SF2M, "Influence des procédés sur la tenue en fatigue, rôle des défauts", 19 May 2010 - 20 May 2010 (Paris, France).

Weiss, Ambrosius and Michel, Laurent and Mahdi, Stephane and Cross, Estelle and Barrau, Jean-Jacques. Influence of ply-drop position in thickness direction on static and fatigue loading behaviour of carbonepoxy laminates. (2009) In: 17th International Conference on Composite Materials (ICCM-17), 27-31 Jul 2009, Edinburgh, United Kingdom .

Mezeix, Laurent and Bouvet, Christophe and Crézé, Serge and Poquillon, Dominique. Fibers networks as a new type of core material. Processing and mechanical properties. (2009) In: Materials Research Society (MRS) 2009, 13-17 Apr 2009, San Francisco, United States .

Michon, Guilhem and Berlioz, Alain and Lamarque, Claude-Henri. A parametrically excited oscillator involving coupling between inclined cable system and deck of stayed bridges. (2009) In: Experimental Vibration Analysis for Civil Engineering Structures, 14-16 Oct 2009, Wroclaw, Poland . (Unpublished)

Weiss, Ambrosius and Michel, Laurent and Mahdi, Stephane and Cross, Estelle and Barrau, Jean-Jacques. Influence de la position dans l’épaisseur des reprises de plis sur le comportement statique et en fatigue pour un stratifié carbone/époxy + Influence of ply-drop position in thickness direction on static and fatigue loading behaviour of carbon fibre/ epoxy laminates. (2009) In: JNC16 - 16èmes Journées Nationales sur les Composites, 10-12 Jun 2009, Toulouse, France . (Unpublished)

Chaussumier, Michel and Shahzad, Majid and Mabru, Catherine and Chieragatti, Rémy and Rezaï-Aria, Farhad. Influence du décapage sur la tenue en fatigue de l'alliage Al7010-T7451 traité par oxydation anodique chromique. (2009) In: CFM 2009 19ème Congrès Français de Mécanique, 24 August 2009 - 28 August 2009 (Marseille, France).

Ledru, Yohann and Piquet, Robert and Michel, Laurent and Schmidt, Fabrice and Bernhart, Gérard. Quantification 2-D et 3-D de la porosité par analyse d’images dans les matériaux composites stratifiés aéronautiques = 2-D and 3-D void quantification with image analyses in aeronautic composite laminates. (2009) In: JNC16 - 16èmes Journées Nationales sur les Composites, 10-12 Jun 2009, Toulouse, France . (Unpublished)

Michon, Guilhem and Berlioz, Alain and Lamarque, Claude-Henri. Couplings in parametrically excited inclined cables systems. (2008) In: 12th Conference on Nonlinear Vibrations, 01-05 Jun 2008, VirginiaTech, United States . (Unpublished)

Limido, Jérôme and Espinosa, Christine and Salaün, Michel and Mabru, Catherine and Chieragatti, Rémy. High speed machining modelling : SPH method capabilities. (2007) In: 4th Smoothed Particle Hydrodynamics European Research Interest Community (SPHERIC) workshop, 27-29 May 2009, Nantes, France .

Prombut, P and Michel, Laurent and Barrau, Jean-Jacques. Mixed-mode delamination of multidirectional composite laminates at 0°/θ° ply interfaces. (2006) In: 12th European Conference on Composite Materials, 29 Aug - 01 Sep 2006, Biarritz, France .

Carpentier, Alban and Michel, Laurent and Grihon, Stéphane and Barrau, Jean-Jacques. Optimization methodology of composite panels. (2006) In: 12th European Conference on Composite Materials (ECCM 12), 29 Aug - 01 Sep 2006, Biarritz, France .

Carpentier, Alban and Michel, Laurent and Grihon, Stéphane and Barrau, Jean-Jacques. Buckling optimization of composite panels via lay-up tables. (2006) In: III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering, 05-09 Jun 2006, Lisbon, Portugal .

Paroissien, Eric and Sartor, Marc and Huet, Jacques and Lachaud, Frédéric. Hybrid (Bolted/Bonded) Joints Applied to Aeronautic Parts: Analytical Two-Dimensional Model of a Single-Lap Joint. (2006) In: 47th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Material Conference, 1 May 2006 - 4 May 2006 (Newport, Rhode Island, United States).

Chieragatti, Rémy and Paroissien, Eric and Huet, Jacques. Faisabilité d'assemblages mixtes boulonnés-collés en aéronautique. (2004) In: Journées Techniques CETIM, 2004 (Saint-Etienne, France). (Unpublished)

Didierjean, Sébastien and Michel, Laurent and Barrau, Jean-Jacques and Paroissien, Eric. Predicting the behavior of graphite/epoxy laminates under hydrothermal loads. (2003) In: EUROMECH 453 Internal Stresses in Polymer Composite Processing and Service Life, 01-03 Dec 2003, Saint-Etienne, France .

Book Section

Paroissien, Eric and Lachaud, Frédéric and Jacobs, Thomas. A Simplified Stress Analysis of Bonded Joints using Macro-Elements. (2013) In: Advances in modeling and design of adhesively bonded systems. Scrivener Publishing LLC, pp. 93-145. ISBN 978-1-118-68637-9

Veran-Tissoires, Stéphanie and Geoffroy, Sandrine and Marcoux, Manuel and Prat, Marc. Chapter 8. Evaporation and Wicking. (2012) In: Wicking in Porous Materials: Traditional and Modern Modeling Approaches. CRC Press, pp. 201-236. ISBN 978-1-4398-7432-5

Gouache, Thibault and Gao, Yang and Gourinat, Yves and Coste, Pierre. Wood wasp inspired space and earth drill. (2010) In: Biomimetics Learning from Nature. InTech - Open Access Publisher, Rijeka, Croatia, pp. 467-486. ISBN 9789533070254

Book

Gourinat, Yves. Exercices et problèmes de mécanique des solides et des structures. Applications aéronautiques et aérospatiales. (2001) (Collection Sciences Sup). Dunod, Paris, France. ISBN 9782100567003

Thesis

Lepesant, Pauline. Mécanismes d'accommodation et débits de premiers et de troisième corps à haute température : étude et modélisation phénoménologique. PhD, Institut National Polytechnique de Toulouse, 2013

Delmas, Anthony. Contribution à l'étude de l'effet mirage : application aux mesures dimensionnelle et thermique par caméras visible proche infrarouge. PhD, Institut National Polytechnique de Toulouse, 2012

Paris, Christophe. Étude et modélisation de la polymérisation dynamique de composites à matrice thermodurcissable. PhD, Institut National Polytechnique de Toulouse, 2011

Taina, Fabio. Optimisation of micrustructure and fatigue properties of Inconel 718 for extrusion die applications. PhD, Génie Mécanique, Mécanique des Matériaux, Institut National Polytechnique de Toulouse, 2011

Shahzad, Majid. Influence de la rugosité et des traitements d’anodisation sur la tenue en fatigue des alliages d’aluminium aéronautiques 2214 et 7050. PhD, Fracture mechanics, Institut Supérieur de l'Aéronautique et de l'Espace, 2011, 274 p.

Michel, Claire. Etude des comportements thermomécaniques et à l'oxydation de réfractaires à base de SiC et à liaison nitrurée employés dans les Unités de Valorisation Energétique d'Ordures Ménagères (U.V.E.O.M.). PhD, Institut National Polytechnique de Toulouse, 2011

Ilyas, Muhammad. Damage modeling of carbon epoxy laminated composites submitted to impact loading. PhD, Génie Mécanique, Institut Supérieur de l'Aéronautique et de l'Espace, 2010, 241 p.

Toral Vasquez, Javier. Identification et modélisation du comportement des structures composites assemblées par cloutage. PhD, Institut Supérieur de l'Aéronautique et de l'Espace, 2009, 267 p.

Castanié, Bruno. Contribution à l'étude des structures sandwichs dissymétriques. PhD, Ecole Nationale Supérieure de l'Aéronautique et de l'Espace, 2000, 208 p.

Lachaud, Frédéric. Délaminage de matériaux composites à fibres de carbone et à matrices organiques : étude numérique et expérimentale, suivi par émission acoustique. PhD, Génie Mécanique, Ecole Nationale Supérieure de l'Aéronautique et de l'Espace, 1997, 295 p.

HDR

Mabru, Catherine. Etats de surface - Matériaux de surface : Résistance à l'endommagement. (2012) [HDR]

Lachaud, Frédéric. Multi scale analysis of composite structures behavior. (2011) [HDR]

This list was generated on Sat Apr 21 07:32:18 2018 CEST.